Skyjacker J32RS Softride Rear Leaf Springs 2-2.5in Lift for Jeep CJ5/CJ6 Willys

Vehicle Fitment

• 1955-1958 Jeep Willys (All Trims, GAS, 4WD & RWD)
• 1959-1960 Jeep CJ5 (All Trims, GAS, 4WD & RWD)
• 1959-1960 Jeep CJ6 (All Trims, GAS, 4WD & RWD)
• 1966-1975 Jeep CJ5 (All Trims, GAS, 4WD)
• 1966-1974 Jeep CJ5 (All Trims, GAS, RWD)
• 1968 Jeep CJ5 (All Trims, DIESEL, 4WD & RWD)
• 1966-1975 Jeep CJ6 (All Trims, GAS, 4WD)
• 1966-1974 Jeep CJ6 (All Trims, GAS, RWD)
• 1968 Jeep CJ6 (All Trims, DIESEL, 4WD & RWD)

Fitment Notes

• Spring width is 1-3/4 in. - verify axle and perch width before installation
• Fits both 4WD and RWD configurations; confirm drivetrain before ordering
• Sold as a pair (2 rear leaf springs per set)
• For use with 2-2.5 in. lift applications only; not compatible with 3.5-4 in. lift configurations
• A Pitman Arm may be required depending on complete lift kit configuration

Features

• Manufactured using American steel for superior strength, durability, and long service life
• Individual leaves are shot-peened with hard steel pellets at high velocity to compress the surface layer and increase tensile strength
• Shot-peening process maximizes wheel travel and ride quality without sacrificing spring longevity
• Uses bolt-style spring clips instead of cinch-style bend clips to eliminate friction and binding between leaves
• Tapered leaf design runs the full length of each leaf, creating more flex at the ends for improved articulation
• Full-length tapering distributes loads more evenly across a greater surface area, reducing leaf-to-leaf digging and wear
• Delivers 2-2.5 in. of rear lift height, improving ground clearance for off-road use and larger tire fitment
• Engineered to maintain factory-like ride quality on-road while enhancing off-road suspension performance
• Skyjacker Softride design allows greater suspension flex during full articulation, keeping tires in contact with uneven terrain

Specifications

• Part Number: J32RS
• Position: Rear
• Lift Height: 2-2.5 in.
• Number of Leaves: 5
• Spring Width: 1-3/4 in.
• Spring Free Arch: 6-1/2 in. (± 1/4 in.)
• Spring Clip Style: Bolt-style (non-friction)
• Material: American-made high-tensile steel
• Surface Treatment: Shot-peened for increased tensile strength
• Drivetrain Compatibility: 4WD and RWD

Included Components

• 2x Skyjacker Softride Rear Lift Leaf Springs (J32RS)

Product Description

The Skyjacker J32RS Softride Rear Lift Leaf Spring is a precision-engineered replacement and upgrade spring designed to deliver 2-2.5 inches of rear lift on 1955-1975 Jeep CJ5, CJ6, and Willys models in both 4WD and RWD configurations. Built from American steel and treated through Skyjacker's proprietary shot-peening process - where hard steel pellets are blasted at high velocities against each leaf surface - these springs achieve significantly higher tensile strength than standard springs. This process is what allows the Softride design to reach maximum wheel travel and ride quality without shortening spring life, something conventional springs simply cannot match.

The Softride design differs fundamentally from typical leaf spring construction in two key ways. First, bolt-style spring clips replace the traditional cinch-style bend clips found on most OEM and aftermarket springs. Cinch clips create friction and binding that restricts flex and accelerates leaf wear; bolt-style clips eliminate that friction entirely, allowing the spring pack to move freely through its full range of motion. Second, each leaf is tapered over its entire length rather than just at the ends. This full-length taper promotes flex at the leaf tips while distributing load stress more evenly across the spring's surface area, reducing the tendency of individual leaves to dig into or damage the leaf above them during articulation.

Sold as a pair, the J32RS springs are a direct bolt-on upgrade for the rear axle of qualifying Jeep platforms and are designed to work within Skyjacker's 2-2.5 in. lift system. They are compatible with a broad range of classic Jeep hardware and are an ideal choice for restorers, trail builders, and vintage off-road enthusiasts looking to increase ground clearance and improve suspension performance on these heritage platforms. A spring width of 1-3/4 in. and a free arch of 6-1/2 in. make these springs suitable for both light trail use and more demanding off-road conditions. Always confirm drivetrain type and spring perch width prior to installation.