Skunk2 907-06-0500 Complete Hardware Kit for EVO VII VIII IX Pro Intake Manifold

Vehicle Fitment

Compatible with Skunk2 Racing Pro Series Intake Manifolds for the Mitsubishi Lancer Evolution VII, VIII, and IX (4G63 engine). This hardware kit is specifically designed for use with the following Skunk2 manifolds:

• Skunk2 Part #307-06-0500 - EVO VII/VIII/IX Pro Series Intake Manifold (Silver)
• Skunk2 Part #307-06-0505 - EVO VII/VIII/IX Pro Series Intake Manifold (Black)

Fitment Notes

• Compatible with the following Mitsubishi Lancer Evolution chassis equipped with the Skunk2 Pro Intake Manifold: 2001-2006 Evolution VII (CT9A); 2001-2006 Evolution VIII (CT9A); 2003-2006 Evolution IX (CT9A) - all variants including RS, GSR, MR, and SE trims
• This kit is for Skunk2 manifolds ONLY - it is not a replacement kit for the factory Mitsubishi OEM intake manifold hardware; all components are specific to the Skunk2 Pro Series manifold's port dimensions, bolt patterns, and fitting locations; do not use with non-Skunk2 manifolds
• This kit addresses the scenario of reassembling a Skunk2 Pro manifold after disassembly, replacing lost or damaged hardware, or completing a used manifold purchase that is missing its original components; if your manifold is intact and fully assembled, this kit is not required

Features

• Complete replacement of all original hardware - the 907-06-0500 restores a Skunk2 EVO Pro Series manifold to its as-new hardware state; every fastener, gasket, fitting, plug, and accessory that originally shipped with the manifold from Skunk2 is included in this single kit, eliminating the need to source individual components from separate suppliers; the kit addresses the most common reasons a technician is missing manifold hardware: disassembly for porting or polishing, replacing a stripped bolt, gasket damage during a prior installation, or purchasing a used manifold without its original documentation and hardware bag
• Viton O-Ring for oil dipstick tubing - Viton is a fluorocarbon elastomer with superior resistance to oil, heat, and chemical degradation compared to standard rubber O-rings; the Viton O-ring seals the oil dipstick tubing interface on the intake manifold, where contact with engine oil and heat cycling requires a durable sealing compound; using the correct O-ring material prevents oil seepage at this interface
• 68mm throttle body gasket - the gasket seals the interface between the Skunk2 manifold's throttle body flange and the 68mm throttle body; a damaged, torn, or missing throttle body gasket causes an unmetered air leak at the throttle body-to-manifold connection, which the ECU cannot compensate for and results in lean air/fuel ratios, idle instability, and drivability issues; this is one of the most commonly needed replacement items after manifold removal and reinstallation
• Fuel rail spacers - the two fuel rail spacers provide the correct standoff height and alignment between the Skunk2 manifold's fuel rail mounting bosses and the fuel rail assembly; using the correct spacers ensures proper injector insertion depth and fuel rail alignment, which affects injector O-ring sealing and injector spray targeting
• Hex socket plugs - the four 1.125" hex socket plugs are used to close off manifold ports that are not in use for a given installation configuration (e.g., vacuum ports, sensor bungs, or auxiliary fittings that are not connected in a specific build); plugging unused ports prevents vacuum leaks and contamination ingestion at open port locations
• M6x1.0x10mm flange bolts - three flange bolts provide the fastening hardware for manifold assembly sub-components; flange-head bolts distribute clamping load over a larger bearing surface than standard hex bolts, reducing the risk of fastener pull-through or gasket damage in aluminum manifold applications
• Pro Series Intake Technology Badge - the Skunk2 branding badge that attaches to the manifold exterior; typically installed at a visible location on the intake manifold body
• Fittings - the kit includes the manifold fittings for hose connections (vacuum lines, boost reference lines, PCV connections, and similar) that attach to the manifold body; these are among the components most frequently lost during manifold removal or damaged during disassembly

Specifications

• Part Number: 907-06-0500
• Brand: Skunk2 Racing
• Product: Complete Assembly Hardware Kit - EVO VII/VIII/IX Pro Series Intake Manifold
• Compatible Manifolds: Skunk2 307-06-0500 (Silver), 307-06-0505 (Black)
• Vehicle Application: 2001-2006 Mitsubishi Lancer Evolution VII/VIII/IX (4G63)

Included Components

• 3x Flange Bolt M6x1.0x10mm
• 2x Fuel Rail Spacer
• 1x Pro Series Intake Technology Badge
• 4x Hex Socket Plug 1.125"
• 1x Oil Dipstick Tubing
• 1x Viton O-Ring
• 1x 68mm Throttle Body Gasket
• Fittings (multiple - as originally shipped with manifold)

Product Description

The Skunk2 907-06-0500 is the Complete Assembly Hardware Kit for the Skunk2 EVO VII/VIII/IX Pro Series Intake Manifold - a replacement set of every hardware component, gasket, fitting, and accessory that originally ships with the Skunk2 Pro manifold (part numbers 307-06-0500 silver and 307-06-0505 black) for the Mitsubishi Lancer Evolution VII through IX. Skunk2 Racing, founded in 1994 in Norco, California, produces the Pro Series manifold for the EVO's 4G63 turbo engine as a high-flow replacement for the factory intake manifold, and the 907-06-0500 service kit exists to restore a Pro manifold to its complete hardware state after disassembly, component loss, or used-manifold purchase.

The kit covers the full range of hardware scenarios: the 68mm throttle body gasket is needed anytime the throttle body is removed and reinstalled; the Viton O-ring seals the oil dipstick tubing interface; the fuel rail spacers establish correct rail alignment and injector depth; the hex socket plugs close off unused ports to prevent vacuum leaks; the M6 flange bolts provide manifold sub-assembly fastening; and the fittings restore the hose connection points for vacuum, boost, and PCV routing. All components are produced to the same specifications as the original hardware shipped with the manifold, ensuring that a reassembled Pro manifold performs identically to one assembled from new.

Compatible exclusively with Skunk2 Pro Series EVO manifolds (307-06-0500 and 307-06-0505). Not for OEM Mitsubishi intake manifold hardware replacement.