Hellwig 7709 Rear Sway Bar for 2009-2026 Dodge/Ram 1500 2WD/4WD Stock Height

Vehicle Fitment

• 2009-2010 Dodge Ram 1500 (All Trims, 2WD/4WD, All Engines, Stock Height to 2" Lift)
• 2011-2026 Ram 1500 (All Trims, 2WD/4WD, All Engines, Stock Height to 2" Lift)

Fitment Notes

• Fits stock ride height through 2" of rear lift - not intended for lifts exceeding 2".
• Fits both 2WD and 4WD configurations across all trim levels and engine options.
• This bar reuses the factory rear end links - end links are NOT included in the kit.
• Ram 1500 models that did NOT come equipped with a factory rear sway bar (certain trim levels) require the Hellwig 7961 End Link Kit, sold separately, for complete installation.
• Ram 1500 models that came equipped with a factory rear sway bar do not require the 7961 kit - the factory end links are reused directly.
• The 2009-2010 model years were sold under the Dodge Ram 1500 nameplate; 2011 and later use the Ram 1500 nameplate. Suspension architecture is consistent across the full range.

Features

• Adjustable-rate rear sway bar engineered specifically for the 2009-2026 Ram 1500 platform - provides a meaningful improvement in lateral stiffness over the factory bar.
• 7/8" (0.875 in.) diameter solid, heat-treated 4140 chromoly spring steel - larger than stock for improved roll resistance and a more planted, controlled rear end during cornering.
• Adjustable rate design allows owners to tune stiffness to match driving conditions, from everyday unloaded commuting to towing and loaded hauling.
• Reduces side-to-side body sway and rear body lean, keeping weight more evenly distributed across all four tires during cornering and lane changes.
• High-durometer polyurethane bushings included for superior roll resistance, reduced noise and vibration, and longer service life than rubber.
• Heat-formed as a single piece from 4140 chromoly steel - more structurally consistent at the bends than cold-bent alternatives.
• Gray hammertone powdercoated finish for long-term corrosion resistance.
• Quick bolt-on installation using factory mounting locations - all hardware included.
• ISO 9001:2015 certified manufacturing at Hellwig's Visalia, California facility. Made in the USA. Backed by a Limited Lifetime Warranty.

Specifications

• Part Number: 7709
• Bar Diameter: 7/8" (0.875 in.)
• Bar Material: Solid, heat-treated 4140 chromoly spring steel
• Finish: Gray Hammertone Powdercoated
• Position: Rear
• Rate Type: Adjustable
• Drivetrain: 2WD and 4WD
• Ride Height: Stock to 2" lift
• End Links: Reuses factory end links (not included); Hellwig 7961 kit required for trucks without factory rear sway bar
• UPC: 745662077099
• Warranty: Limited Lifetime

Included Components

• 1x Hellwig 7709 Rear Sway Bar (7/8" diameter, chromoly, gray hammertone powdercoated)
• 1x Set of high-durometer polyurethane bushings
• 1x Complete mounting hardware kit
• 1x Installation instruction sheet

Product Description

The Hellwig 7709 Rear Sway Bar is a direct-fit adjustable-rate suspension upgrade for the 2009-2026 Dodge/Ram 1500 in both 2WD and 4WD configurations. While the Ram 1500 does come equipped with a factory rear sway bar on most trim levels, the stock bar is sized for ride comfort rather than meaningful roll resistance - leaving the truck prone to noticeable body lean through corners and side-to-side sway during lane changes or towing maneuvers. The Hellwig 7709 addresses this with a solid 7/8" heat-treated 4140 chromoly bar that is larger in diameter than stock, delivering improved lateral stiffness, better cornering behavior, and a more controlled rear end feel both empty and under load.

The adjustable-rate design is a key advantage, allowing owners to select the stiffness level that best matches their use case - from moderate everyday driving to more aggressive towing or performance-oriented setups. The bar is engineered to reuse the factory rear end links on trucks that came from the factory with a rear sway bar, simplifying the installation process. Owners of Ram 1500 models that were not originally equipped with a rear sway bar (available on certain trim levels) will need the separately sold Hellwig 7961 End Link Kit to complete the installation. All other mounting hardware and polyurethane bushings are included, and the installation is bolt-on using the factory rear axle mounting points. Fitment spans stock ride height through 2" of rear lift.

Coverage spans the full 2009-2026 production run of the Ram 1500, including both the Dodge-badged 2009-2010 models and the Ram-badged 2011-2026 models, across all trim levels, engine options, and both 2WD and 4WD configurations. Built at Hellwig's ISO 9001:2015 certified Visalia, California facility and backed by a Limited Lifetime Warranty, the 7709 is a proven, affordable American-made upgrade that brings noticeably better rear handling dynamics to one of the most popular truck platforms on the market.