DBA DBA2659E-10 EnShield Rear Rotor for Subaru WRX BRZ Forester FR-S 86 286mm

Vehicle Fitment

• 2008-2021 Subaru Impreza WRX (GR/GV 2008-2014; VA 2015-2021 models WITHOUT Eyesight, EJ255 / FA20DIT, AWD) - Rear Axle
• 2004-2016 Subaru Forester XT (SG 2004-2008 XT; SH 2009-2013; SJ 2014-2016 XT, AWD) - Rear Axle
• 2009-2013 Subaru Forester (SH, all engine variants with rear disc brakes, AWD) - Rear Axle
• 2013-2020 Subaru BRZ (ZC6, 2.0L FA20D, RWD) - Rear Axle - see Fitment Notes
• 2013-2016 Scion FR-S (ZN6, 2.0L FA20D, RWD) - Rear Axle
• 2017-2019 Toyota GT86 (ZN6, 2.0L FA20D, RWD) - Rear Axle
• 2008-2013 Subaru Impreza (GE / GH, 2.0L / 2.5L, AWD / FWD) - Rear Axle
• 2010-2014 Subaru Legacy / Outback (BR / BS, 2.5L / 3.6L, AWD) - Rear Axle

Fitment Notes

• Sold individually - two rotors are required for a complete rear axle replacement.
• The "-10" suffix in the part number denotes a 10-stud-hole hub pattern, accommodating both 5x100mm and 5x114.3mm bolt circle configurations across the applicable Subaru and Toyota/Scion platforms.
• 2013-2015 Subaru BRZ / Scion FR-S: This rotor applies to models fitted with the standard 286mm rear disc. Certain BRZ variants (particularly the 2013 Limited) were fitted with a larger 297mm rear rotor - confirm your existing rear rotor diameter before ordering.
• 2015-2021 Subaru WRX (VA): Applies to models WITHOUT Eyesight driver assistance. WRX STI is not covered by this part number - the STI uses a Brembo rear caliper and a different rotor specification.
• This is an EnShield (E suffix) standard smooth rotor - not slotted or cross-drilled. It is the OE-profile replacement rotor with full-surface corrosion protection coating. For a T2 slotted version on the same application, refer to DBA2659S-10.
• Due to the wide platform coverage, verify your existing rear rotor diameter (286mm) before ordering if your vehicle has had brake system modifications.

Features

• EnShield full-surface corrosion protection: a zinc/aluminium water-based coating is applied to the entire rotor surface - including the hat, non-friction areas, and vane channels - and then baked on. This prevents the cosmetic rust and surface corrosion that typically forms on bare iron rotors during storage and in wet climates, and keeps the rotor looking new throughout its service life.
• EnShield rotors do not require pre-installation cleaning with brake cleaner prior to fitting - the coating is ready to install straight out of the box.
• Street Series OE-profile replacement - manufactured to DBA's above-OEM standards for dimensional accuracy, with CBN (Cubic Boron Nitride) machine-turned friction surface finish to minimise disc thickness variation and reduce brake shudder or pedal judder.
• Centre-split core casting design enhances heat transfer and thermal efficiency across the rotor body.
• Direct OE-replacement fit across the GR/GV WRX, VA WRX, ZC6 BRZ/FR-S/GT86, SH/SJ Forester, and GE/GH Impreza platforms - no caliper or bracket modifications required.
• Ideal for daily drivers and commuters seeking a long-lasting, rust-resistant OE-quality rear rotor replacement on these popular Subaru/Toyota platforms.

Specifications

• Position: Rear axle
• Series: Street Series EnShield (plain/smooth)
• Rotor Type: One-piece, solid (non-vented), non-directional
• Outside Diameter: 286mm (11.26 in.)
• Nominal Thickness: 10mm
• Discard Thickness: 10mm
• Overall Height: 63.5mm
• Centre Hole Diameter: 58mm
• Stud/Lug Holes: 10 (dual bolt pattern: 5x100mm and 5x114.3mm)
• Surface Type: Smooth (OE profile)
• Finish: Full-surface EnShield zinc/aluminium baked-on coating
• Warranty: 12 months or 20,000 km from date of purchase
• Part Number: DBA2659E-10

Included Components

• 1x DBA DBA2659E-10 Street Series EnShield Rear Brake Rotor (single rotor - order 2 for a complete rear axle set)

Product Description

The DBA DBA2659E-10 Street Series EnShield Rear Brake Rotor is a direct OE-replacement solid rear rotor covering one of the most widely shared brake specifications in the Subaru and Toyota/Scion performance platform ecosystem. The 286mm solid rear disc is the standard rear specification for the Subaru Impreza WRX (2008-2021, excluding WRX STI), Subaru BRZ / Scion FR-S / Toyota GT86 (2013-2019, standard brakes), and Subaru Forester XT (2004-2016), making DBA2659E-10 a high-volume replacement rotor across multiple generations of these popular platforms.

What distinguishes the DBA2659E-10 from a standard bare-iron replacement rotor is the EnShield full-surface corrosion protection coating. The entire rotor - including the hat, vane channels, and non-friction areas - is coated with a zinc/aluminium water-based solution and baked on at the factory. This eliminates the surface rust that immediately forms on uncoated rotors in humid or wet conditions, keeps the rotor looking clean behind the wheel throughout its service life, and means no pre-installation cleaning is required. The EnShield coating does not affect the friction surface performance - the CBN machine-turned disc face delivers the same dimensional precision and smooth bed-in as any DBA Street Series rotor.

The "-10" suffix denotes the 10-stud-hole hub pattern, which accommodates both 5x100mm and 5x114.3mm bolt circle configurations across the applicable Subaru and Toyota platforms. Sold individually; two units are required for a complete rear axle replacement. For drivers who also want the added bite of T2 bi-symmetrical slots on this same application, the companion part DBA2659S-10 is available. Backed by DBA's 12-month/20,000km manufacturer's warranty.