Air Lift 57264 LoadLifter 5000 Air Spring Kit for 2023-2026 Toyota Sequoia 4WD

Vehicle Fitment

• 2023-2026 Toyota Sequoia SR5 (4WD)
• 2023-2026 Toyota Sequoia Limited (4WD)
• 2023-2026 Toyota Sequoia Platinum (4WD)
• 2023-2026 Toyota Sequoia Capstone (4WD)
• 2023-2026 Toyota Sequoia TRD Pro (4WD) - see Fitment Notes
• 2025-2026 Toyota Sequoia 1794 Edition (4WD)

Fitment Notes

• Does not fit TRD Pro models equipped with Fox rear remote reservoir shocks - the Fox reservoir prevents proper air spring mounting in the rear suspension
• TRD Pro models equipped with standard (non-Fox remote reservoir) rear shocks may be compatible - verify rear shock configuration before ordering
• 4WD application only - fitment for 2WD (RWD) Sequoia variants has not been confirmed by Air Lift
• No frame drilling required - kit bolts directly to existing suspension mounting points using common hand tools
• Compatible with most factory in-bed hitch configurations
• Replacement air spring for this kit: PN 50364

Features

• Provides up to 5,000 lbs. of rear load-leveling capacity, working in tandem with the Sequoia's factory coil spring suspension to maintain proper ride height under heavy towing and hauling loads
• Double-bellow air spring design delivers precise, adjustable load support from 5 to 100 PSI - dial in the exact pressure for any load from empty to maximum GVWR
• Eliminates rear squat, trailer sway, body roll, poor headlight aim, and bottoming out that occur under heavy towing or payload conditions
• Upper and lower roll plates protect air springs from sharp frame edges and road debris, extending service life under demanding conditions
• Ultra-high-strength nylon composite end caps are as strong as steel but lighter and fully corrosion-proof for long-term durability
• Air springs reinforced with 2-ply fabric construction - built similarly to tires for maximum strength and flexibility across the full pressure range
• Underframe mounting design works with most factory in-bed fifth wheel and gooseneck hitch configurations without interference
• No frame drilling required - complete bolt-on installation using only common hand tools
• Compatible with Air Lift's WirelessAir, WirelessOne, and LoadController on-board compressor systems for on-the-go pressure adjustment from inside the vehicle
• Backed by Air Lift's limited lifetime warranty and 60-day ride satisfaction money-back guarantee

Specifications

• Position: Rear axle
• Application Type: Rear kit
• Air Spring Type: Double-bellow with upper and lower roll plates
• Load Leveling Capacity: Up to 5,000 lbs.
• Minimum Air Pressure: 5 PSI
• Maximum Air Pressure: 100 PSI
• End Cap Material: Ultra-high-strength nylon composite (corrosion-proof)
• Drilling Required: No
• Package Weight: 25.4 lbs.
• Package Dimensions: 14.125" W x 9.25" D x 10.75" H
• Replacement Air Spring PN: 50364
• Warranty: Limited lifetime, no mileage restriction

Included Components

• 2x LoadLifter 5000 double-bellow air springs
• 2x Upper roll plates
• 2x Lower roll plates
• 1x Complete mounting hardware kit (all brackets, nuts, bolts, and fasteners needed for installation)
• 1x Illustrated installation guide

Product Description

The Air Lift 57264 is a purpose-built LoadLifter 5000 air spring kit engineered specifically for the 2023-2026 Toyota Sequoia 4WD. The third-generation Sequoia moved to a coil-spring rear suspension setup - and while that design delivers an excellent unloaded ride, it can allow significant rear squat, sway, and headlight misalignment when towing a trailer or carrying a heavy payload. The 57264 addresses this directly by installing double-bellow air springs between the rear axle and frame, working alongside the factory coil springs to provide up to 5,000 lbs. of supplemental load-leveling capacity. The springs are fully adjustable from 5 to 100 PSI, giving the driver precise control over rear ride height regardless of load - run them nearly empty when unloaded for a factory-like ride, or pressurize as needed to level the vehicle when towing a boat, travel trailer, or fifth wheel.

Installation requires no frame drilling and uses only common hand tools. The kit mounts underframe through existing attachment points, keeping the installation clean and reversible. Each air spring is reinforced with 2-ply fabric construction and protected by upper and lower stainless steel roll plates that shield the rubber from sharp frame edges. The end caps are molded from ultra-high-strength nylon composite - comparable to steel in strength but significantly lighter and immune to corrosion. All trims across the 2023-2026 Sequoia lineup are supported, including the SR5, Limited, Platinum, Capstone, and 1794 Edition, as well as TRD Pro models - with one exception: TRD Pro Sequoias equipped with Fox rear remote reservoir shocks cannot be fitted due to reservoir clearance conflicts at the rear suspension mounting area. Buyers with TRD Pro models should verify their rear shock configuration before ordering.

The 57264 is compatible with Air Lift's full range of on-board compressor systems, including the WirelessAir, WirelessOne, and LoadController, enabling real-time pressure adjustment from the driver's seat without leaving the cab. This makes it an ideal companion for Sequoia owners who frequently transition between loaded and unloaded driving. Air Lift backs the kit with a limited lifetime warranty covering defects in materials and workmanship with no mileage restriction, plus a 60-day ride satisfaction money-back guarantee. The replacement air spring for this kit is PN 50364.